Hi Alex,I have uploaded another picture showing the power supply area, I have also uploaded the copper foil patterns I put together in Paint Shop Pro for the linear regulator section to give you some idea of the layout. Circuit wise it's just a collection of 20mm fuses and basic fixed voltage regulators taken straight from datasheets, fuse overkill ?? maybe but I prefer that to melted/burned PCB's :-)The case parts I used are not one of the complete cases that Modushop sell but ordered from the case spare parts section of the website, I didn't want to pay for parts I am not going to use as I will eventually have a custom front and back panel made. The Dissipante range you mention has heavy heatsinks for power amplifiers and so is not suitable.The extruded case sides are from the 'Slimline and Galaxy' range 4U in height and 350mm long, shame they dont make longer sections as standardand the case bottom is from the 'Cover Slim Line' range 350mm in depthI also have a fully vented top cover but have not shown this (again 350mm in depth)4U is a bit tight height wise but with careful planning it looks like the top lid will go on ok.Modushop.biz are based in Italy, I am in the UK so shipping outside of Italy isn't an issue to themhope this helpsregardsDavid Fry
On Monday, March 3, 2014 3:12:13 PM UTC, Alexander wrote:Your fitment sure does look good. Which of their cases did you use? I see the Dissipate 5U, which looks similar. Too bad they're on the other side of the pond, from me, or I might consider doing the same. If you can, I'd like to see some pictures of your PSU installation.Thanks!- Alex
On Mon, Mar 3, 2014 at 8:57 AM, David Fry <dgf...@googlemail.com> wrote:
Hi all,8 months after my first contact/enquiry to John Monahan regarding building a S100 computer I now have the hardware up and running as far as the Z80 monitor.The boards currently build and fitted are:-S100 V2 Z80 CPU card (running at 6mhz at the moment)S100 V1 RAM&ROM cardS100 V2 IDE Interface cardS100 V1 Console I/O cardS100 V2 Bus extender card (just for the reset button)The main power supply rails are switch mode (+8v, +16v, -16v) with secondary linear regulators (+5v, +12v) to power the onboard hard disk/floppy drive.The outer case metalwork (extruded sides & aluminium base) was purchased from http://www.modushop.biz/ecommerce/index_l2.phpit's essentially case metalwork for audio/hifi projects but I liked the idea of sliding the power supply modules & disk drives into the 'T' slotted sides and it allows me to change my mind on drives etc... over time.The 10 slot active terminated backplane came from Herb Johnson (Retrotechnology.com)I have uploaded a couple of pictures to the N8VEM workspace to encourage others who are still working on their first S100 systemI'd like to thank both John and Andrew for the hours of fun so far in putting this system together, i'm sure it's not all going to be plain sailing though which brings me to my first question.I have noticed in the Z80 monitor (v5.02) that once the screen is filled with characters and starts to scroll the cursor prompt disappears !!, the monitor still responds to commands though and all functionality otherwise seems fine. Can anyone else replicate/confirm this, it's not a biggie but thought I would mention it.Now I'm off to try and burn the IDE diagnostic test utility onto an EEPROM to check out the IDE board before working out how to get CP/M 3 up and running.regards and happy solderingDavid Fry--To unsubscribe from this group and stop receiving emails from it, send an email to n8vem-s100+...@googlegroups.com.
You received this message because you are subscribed to the Google Groups "N8VEM-S100" group.
For more options, visit https://groups.google.com/groups/opt_out.